#LOGIC PRO X 10.3 INTERFACE DIAGRAM UPDATE#
#LOGIC PRO X 10.3 INTERFACE DIAGRAM SOFTWARE#
#LOGIC PRO X 10.3 INTERFACE DIAGRAM PROFESSIONAL#

This means that the muted signal can be monitored without it feeding the main mix bus and then switched in to the main mix with the Mute button РІР‚вЂњ perfect for live webcasting because a remote feed can be monitored РІР‚ВofflineРІР‚в„ў and punched in to the broadcast feed. Bus B can be used as a convenient DAW record send but it can also be routed to the monitor matrix. The fader channels all have proper PFL and a Mute button that routes the muted signal to a РІР‚ВBus BРІР‚в„ў. The Master Section has main and alternate monitor outputs with a proper monitor source matrix, as well as mono check, dim and cut. It has two Stereo Cue buses (with level and pan controls) for individual artist foldback mixes.

#LOGIC PRO X 10.3 INTERFACE DIAGRAM PROFESSIONAL#

SiX has a collection of professional routing & monitoring features taken directly from our large format console heritage. We spent some time working on alternate fader tapers and settled on a law that gave us the most control over the most useable gain range, making on-stage level control far easier than it would be with a rotary or a 60mm fader as found on other compact mixers.Р”В®ach channel has a fully balanced insert point for integrating other signal processors which is after the EQ and Compressor circuits, and like all SSLs the insert send is always active РІР‚вЂњ meaning you can use this as a РІР‚СљdryРІР‚Сњ record send to your DAW if required.Р”Р„t the bottom of the mono channels we have an ALTernate input switch which can source 2 extra mono channels from a connector on the rear of the console which can be used at mixdown. This approach draws upon the SSL design legacy of specifying response curves and centre frequencies for channel EQ that are immediately intuitively pleasing in their response these curves and frequencies were selected by our team as the most РІР‚Сљmusically usefulРІР‚Сњ for a wide range of sources. This is a cool-sounding circuit that makes it simple to dial in a consistent level and get signals sitting right in the sweet spot.Р”В«oth mono channels have a new two-band SSL EQ that may be independently switched between shelf and bell curves, with different centre frequencies for each type. Simply adjust the threshold, watch the traffic lights flash to see how much compression is happening and rely on the circuit to automatically adjust gain to match input levels. It has a program-dependent attack time, a fixed release time and fixed ratio. This design is based on and has the same sound as the classic SSL feed-forward Channel Compressor circuit. Moving down the channel strip we have a brand-new one knob compressor circuit. They have phantom power, 75Hz high pass filter and an independent line-level input which can be switched to instrument level input with high impedance. In my upcoming posts I will use the IOC feature to interface the keypad.SiX has two mono channels with SSL SuperAnalogueРІвЂћСћ MicРІР‚в„ў PreРІР‚в„ўs these are transparent, fast and have a much wider available gain range than you would typically get on a compact desktop mixer РІР‚вЂњ 66dB of gain compared to the more typical mid-40s or 50dB found in desktop mixers. By using the feature without any change in the hardware setup we can scan the keypad in the ISR and have more of the controllerРІР‚в„ўs time to do something useful. In PIC the whole of PORT B has this feature. As the name suggests, the controller will interrupt if it finds any change in a port. There is a cool feature on Microcontrollers called as the Interrupt on Change (IOC). The above program is done with polling and utilizes the entire time of the controller to scan the keypad and display the data on the 7 segment displays.

Here is a video demonstration for the interface of the 4x4 matrix keypad using the above code.

#LOGIC PRO X 10.3 INTERFACE DIAGRAM UPDATE#

*-Function Declaration-*/ void seg_wrt ( void ) void update ( unsigned char ) unsigned char val = 0 void main ( void ) #pragma config OSC=HS,WDT=OFF,FCMEN=ON,XINST=OFF,IESO=OFF,LVP=OFF

#LOGIC PRO X 10.3 INTERFACE DIAGRAM SOFTWARE#

In the image, black line symbolizes logic 0 and red line symbolizes logic 1.Р”Р‡or now let us assume that, the circled key is pressed and see how the key press can be detected by a software routine.

The first step involved in interfacing the matrix keypad is to write all logic 0РІР‚в„ўs to the rows and all logic 1РІР‚в„ўs to the columns. Here are the steps involved in determining the key that was pressed. The colors red and black is for logic high and low respectively. Using this logic, the button press can be detected. This will drive that column pin (initially high) low.

When any one of the switches are pressed, the corresponding row and column are connected (short circuited). So there is no connection between the rows and columns. Initially all switches are assumed to be released. We will use this feature to detect the button that was pressed in the following sections. From the circuit you can see that when one of the 16 buttons are pressed, a pair of pins are connected together.

Logic pro x 10.3 interface diagram